Fastway® Flip™ Automatic Jack Foot

Flip™ Jack Foot

$1.27$49.99

5.00 out of 5
(3 customer reviews)

Tired of hauling around and stacking up old 2x4s, just so you can get a little more height from your jack?  The new Fastway® Flip™ takes care of those hassles for good.

Clear selection

Product Description

flip123combined

logo_flip

The Flip jack foot attaches permanently to the bottom of your jack’s inner tube.  As you extend your jack, the Flipjack foot extends down, and locks into place.  When you raise your jack, the Flip jack foot automatically tucks up under the frame and out of the way!

There are three Flip size options:

  1. 6″ Flip jack foot to fit a 2-1/4″ jack
  2. 4″ Flip jack foot to fit a 2-1/4″ jack
  3. 6″ Flip jack foot to fit a 2″ jack

To figure out what Flip will work best for your trailer click the “Specifications” tab

Find the Flip jack foot that works best for you.

Flip Jack Foot
Part # Part Max Tongue Weight Max Lift Capacity Fits Included
88-00-4500 4” Flip jack foot for 2-1/4” jack 1,600 lbs. 4,000 lbs. Manual or electric 2-1/4” jack with 2” diameter round or 2” square inner jack tube spacer ring and mounting hardware
88-00-6500 6” Flip jack foot for 2-1/4” jack 1,400 lbs. 4,000 lbs. Manual or electric 2-1/4” jack with 2” diameter round or 2” square inner jack tube spacer ring and mounting hardware
88-00-6525 6” Flip jack foot for 2” jack 1,400 lbs. 4,000 lbs. Manual or electric 2” jack with 1-7/8” diameter round or 1-7/8” square inner jack tube spacer ring and mounting hardware

Which Width?

whichwidth The Flip jack foot come in two widths. One to fit a 2-1/4″ jack, and one to fit a 2″ jack. To find out what size jack you have measure the width of your jack above the trailer frame (as shown in the illustration to the right.) - A 2-1/4″ Flip fits almost all standard tongue jacks (95+%). - A 2″ Flip fits very small trailers and some electric tongue jacks.

Which Height?

whichheight With the trailer hitched as you usually tow: – If there is 8″ to 10″ from the bottom of the outside jack tube to the ground use a 4″ tall Flip jack foot. – If there is more than 10″ from the bottom of the outside jack tube to the ground use a 6″ tall Flip jack foot. General Rule Average height person with trailer coupled to tow vehicle: - If the top of your trailer frame sitsabove the bottom of your knee cap you probably need a 6″ tall Flip jack foot. - If it sits below the bottom of your knee you probably need a 4″ tall Flip jack foot.

4″ Flip Jack Foot

The 4″ Flip works best on trailers with low decks like horse trailers, flatbed trailers, some older model RV Travel trailers and small single axle trialers. 4fliptrailers

6″ Flip Jack Foot

The 6″ Flip works best on trailers with taller decks like over the axle flat bed trailers, enclosed cargo trailers, atv/snowmobile V-nose trailers and newer RV travel trailers. 6fliptrailers

3 reviews for Flip™ Jack Foot

  1. 5 out of 5

    :

    I wish you could see a picture of the big chunk of wood that used to rest under my trailer foot. It was a monolith. Not only does this make the trailer look so much better, it saves me a ton of cranks. Great product.

  2. 5 out of 5

    :

    Before giving this review, I must remark that what it replaced was a 12″ tall stump that we used after the toe on our previous jack foot was broken off (we won’t get into that story). It was easy and fairly quick to install, and has been terrific to use – the best we have had experience with in all the trailers and toy haulers we have had. Would highly recommend it to anyone.

  3. 5 out of 5

    :

    My flip is awesome! No more dirty spider-ridden wood block with my camping gear in the truck go under the jack and take up the slack (crank forever). Now I use the flip and it’s just as fast, but 10x lighter, cleaner, and more convenient.

Add a review